My laser engraver from 0 knowledge to 32.461% .... probably

[BobbyW]

Hello everyone. So , is my first post here obviously , and from totaly "0" knowledge of CNC machines or GCODE i start to build my own laser engraver ,cutter, whatever will be  :o.
First thanks to Art and tweakie for first advices what i should buy and try for laser engraver. Initialy i want to build for my wife and fun but after time passing , i take it personaly, is alot of learn about CNC machines and that keep me interested on.
Good things and bad things about my start always are, of course.
Good one's has, i just start without any schematic and i just adjust everything in work procces. I buy newma 23 2.0n clossed loop stepper , pokeys57CNC and of course auggie . Start like a charm. I didn't finish to install the laser yet but i hope i managed to calibrate the steps ,axes, everything. Some limits switch missing but soon will be done too. I manage to learn how to tune and set in pokeys ......i'm up,,, i think  ::)
Bad things , i didnt realy understand how all GCODE comands work " time is to short " to much information on strange field for me .
Second , i don't manage to install augie correctly on lenovo w530 64bit win7 pack1, i7.8G ram, SSD. I got some strange error on start to install auggie " this program stop" and after windown recover the problem and install work correctly, probably my stupid antivirul open in sandbox first. But it work.
Other thing is , until 2 min of trying push Estop i got engaged, disengaget message and i need to push again Estop until 20 times to get working. That happen only on network, USB work perfectly. I try in bridge, DHCP router only and home router linksys EA6900 , fixed IP, private class, everything. Probably is misssconfiguration in profile , i dont know.
Other is PWM, i didnt manage to try on others pins, but is engaged on analog out at 17 i think 0-10v, still dont have time to measure everything correctly. That in the feature. I read here to use others pins from trusted user , tweakie.
I'm electronic engineer, ASM , C programmer but is first time on CNC mashining, is alot to learn and ...
So that's it..... i'm up
I put some pictures below , and ignore the mess, is for everyone of as who learning.....
Critics are welcome and sry for my poor english
Still i didn't figure out how to load DXF in auggie for cutting and in wich program i should use to build the vector

[ArtF]

Bobby:

  Well , your off to a good start being that you managed to tune your steppers and such.

>>Other thing is , until 2 min of trying push Estop i got engaged, disengage t message and..

  Check your network delay setting in the final page of axis settings. Some need 1, some need 0
in that setting for network use.

>>Still i didn't figure out how to load DXF in auggie for cutting and in wich program i should use to build the vector

  You can load a dxf into Vexx and select all contours, then edit/group, then press the quickGcode button. This
will put out code for lasers from a dxf. Auggie will only load photos to make Gcode from, not dxf's. It will load
Vexx's Gcode though.


  Yell when confused..

Art

[tweakie]

Hi Bobby,

Will it be a CO2 laser that you are installing and what is the wattage ?

Tweakie.

[Mooselake]

Hi Bobby!

Welcome to the forum!  I don't know means you realize there's always more to learn, and despite some occasional frustration that's where the fun is.  Keep us posted on how you're doing, and don't forget those safety glasses, only takes seconds to ruin your eyes.

Hi Tweakie!  When did you add a forum to your site, and is that a new host?

Kirk

[tweakie]

Hi Tweakie!  When did you add a forum to your site, and is that a new host?

Hi Kirk,

I had to change website hosting following a change of policy by my service provider. The website was added just so that different 8 bit image laser engraving techniques could be discussed but unfortunately there has been little or no interest.

Tweakie.

[BobbyW]

Hi Bobby,

Will it be a CO2 laser that you are installing and what is the wattage ?

Tweakie.

Is 80w tube, same the source. I test recently to adjust maximum current alowed , to dont damage the laser, and i notice , the laser source on TTL input have a residual internal voltge at 600mv. That will turn laser on with alot of power(without input signal). Also at 2.4V input i reach 22mA. That is normal or the power source dont work corectly?
Thanks

[tweakie]

Hi Bobby,

Could you perhaps post some details of your laser PSU / controller ?

Tweakie.

[ArtF]

Hi:

yeah, its hard to tell whats up without knowing how its hooked up.
The PWM puts out a tickle voltage which yours may not need, so you may want to set tickle at 0 in the settings.
But then there should be no voltage when laser is off..

Art

[BobbyW]

Hi Bobby,

Could you perhaps post some details of your laser PSU / controller ?

Tweakie.

Yes sure. I didn't think on that, sry. 
The source is this one https://www.aliexpress.com/item/911254124.html?spm=a2g0o.productlist.0.0.490f6f3e9u1QMx&algo_pvid=15f05b4c-2cb1-45f9-900e-8eb87797684d&algo_expid=15f05b4c-2cb1-45f9-900e-8eb87797684d-2&btsid=c82436b8-a867-4703-8316-1c5aa42280ac&ws_ab_test=searchweb0_0,searchweb201602_,searchweb201603_52

and laser is this one https://www.aliexpress.com/item/32784065931.html?spm=2114.12010612.8148356.4.2ce43a39J6FNuq

will open the source this weekend to see what is the problem , or just working like that , i dont know. But normaly , any input should offer more high impedance possible with 0 residual voltage .
Thanks

[tweakie]

I think a simple test would be to disconnect anything connected to the TTL(H) and TTL(L) terminals of the PSU.
If the laser still fires try fitting a pull-up resistor (10k) between TTL(L) and +5V and a pull-down resistor (10k) between TTL(H) and GND.
If the laser still fires then you have a problem with the PSU.